Rear brake rebuild
Moderators: CYBORG, Oldewing, robin1731, Forum Moderators
-
- Cast Iron Member
- Posts: 76
- Joined: Mon Dec 10, 2018 2:14 pm
Rear brake rebuild
Well I finished the front brake rebuild on my 78 now on to the rear. I've ordered caliper rebuild kit and master cylinder rebuild kit still need to find stainless braided brake line. While I have the rear wheel off anything else I should do? I'm planning on putting on a new tire and lubing the final drive while the wheel is off. Any other suggestions?
- Track T 2411
- Honored Life Member
- Posts: 8511
- Joined: Thu May 29, 2008 9:37 pm
- My Album: http://www.ngwclub.com/gallery/v/wingmans/Track+T+2411/
- Location: Prairie du Sac Wisconsin
Re: Rear brake rebuild
IIRC, the rear caliper is 'split' on the '78, and there's an o-ring between the two halves that is not included in rebuild kits. You can find the correct o-ring on Randakk's website. Personally, I always change out the wheel bearings on a new 2 me bike, as well.
"I have no special talent. I am only passionately curious." - Albert Einstein
"He that is good with a hammer tends to think everything is a nail" - Abraham Maslow
"If you can't take the time to do it right the first time, how are you ever going to find the time to do it over?" -Unknown
Current Rides:
'Grumpy' - '81 Standard, now fully dressed.
'Layla' - '81 Standard w/dealer installed fairing and Hondaline bags.
'Scarlett' '76 'Survivor' nekkid as a j-bird!
Under Construction:
The 'Jalopy' '78-'79 Mash-up
'Quikie' '81 gl1100I back on the lift, project with the step-son!
In The Shed:
'81 gl1100I barn find aka "Josie, the farmer's daughter." (almost comatose build)
'77 gl1000, roller parts bike.
'82 gl1100I, 'Old Crusty' titled roller parts bike (free!)
'82 gl1100I, My first 'Wing, and an expensive lesson!
New2U Bike? Read Me.
"He that is good with a hammer tends to think everything is a nail" - Abraham Maslow
"If you can't take the time to do it right the first time, how are you ever going to find the time to do it over?" -Unknown
Current Rides:
'Grumpy' - '81 Standard, now fully dressed.
'Layla' - '81 Standard w/dealer installed fairing and Hondaline bags.
'Scarlett' '76 'Survivor' nekkid as a j-bird!
Under Construction:
The 'Jalopy' '78-'79 Mash-up
'Quikie' '81 gl1100I back on the lift, project with the step-son!
In The Shed:
'81 gl1100I barn find aka "Josie, the farmer's daughter." (almost comatose build)
'77 gl1000, roller parts bike.
'82 gl1100I, 'Old Crusty' titled roller parts bike (free!)
'82 gl1100I, My first 'Wing, and an expensive lesson!
New2U Bike? Read Me.
-
- Cast Iron Member
- Posts: 76
- Joined: Mon Dec 10, 2018 2:14 pm
Re: Rear brake rebuild
Thanks for the advise would that be caliper halves seal part # 100-1156?
- Track T 2411
- Honored Life Member
- Posts: 8511
- Joined: Thu May 29, 2008 9:37 pm
- My Album: http://www.ngwclub.com/gallery/v/wingmans/Track+T+2411/
- Location: Prairie du Sac Wisconsin
Re: Rear brake rebuild
That would be it!bagger13 wrote:Thanks for the advise would that be caliper halves seal part # 100-1156?
"I have no special talent. I am only passionately curious." - Albert Einstein
"He that is good with a hammer tends to think everything is a nail" - Abraham Maslow
"If you can't take the time to do it right the first time, how are you ever going to find the time to do it over?" -Unknown
Current Rides:
'Grumpy' - '81 Standard, now fully dressed.
'Layla' - '81 Standard w/dealer installed fairing and Hondaline bags.
'Scarlett' '76 'Survivor' nekkid as a j-bird!
Under Construction:
The 'Jalopy' '78-'79 Mash-up
'Quikie' '81 gl1100I back on the lift, project with the step-son!
In The Shed:
'81 gl1100I barn find aka "Josie, the farmer's daughter." (almost comatose build)
'77 gl1000, roller parts bike.
'82 gl1100I, 'Old Crusty' titled roller parts bike (free!)
'82 gl1100I, My first 'Wing, and an expensive lesson!
New2U Bike? Read Me.
"He that is good with a hammer tends to think everything is a nail" - Abraham Maslow
"If you can't take the time to do it right the first time, how are you ever going to find the time to do it over?" -Unknown
Current Rides:
'Grumpy' - '81 Standard, now fully dressed.
'Layla' - '81 Standard w/dealer installed fairing and Hondaline bags.
'Scarlett' '76 'Survivor' nekkid as a j-bird!
Under Construction:
The 'Jalopy' '78-'79 Mash-up
'Quikie' '81 gl1100I back on the lift, project with the step-son!
In The Shed:
'81 gl1100I barn find aka "Josie, the farmer's daughter." (almost comatose build)
'77 gl1000, roller parts bike.
'82 gl1100I, 'Old Crusty' titled roller parts bike (free!)
'82 gl1100I, My first 'Wing, and an expensive lesson!
New2U Bike? Read Me.
-
- Cast Iron Member
- Posts: 76
- Joined: Mon Dec 10, 2018 2:14 pm
Re: Rear brake rebuild
Thanks, you would think if you need it the rebuild kit would include it !
- pidjones
- SUPER BIKER!!!!
- Posts: 3238
- Joined: Wed May 22, 2013 4:06 pm
- Location: East TN
Re: Rear brake rebuild
Yes, it is a seal, not an o-ring. No telling why it isn't included, but why isn't reservoir o-ring in master cylinder kits, why aren't fuel port U-rings included in carb kits (instead of bad jets)?
"Love 'em all.... let God sort 'em out!"
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
-
- Cast Iron Member
- Posts: 76
- Joined: Mon Dec 10, 2018 2:14 pm
Re: Rear brake rebuild
I'm just glad Track chimed in and let me know I need one
-
- Similar Topics
- Replies
- Views
- Last post