Carb Cap Crisis
Moderators: CYBORG, Oldewing, robin1731, Forum Moderators
- Dr. Frankenstein
- Silver Member
- Posts: 721
- Joined: Sun Nov 10, 2019 7:22 am
- Location: Charlottesville, VA
Carb Cap Crisis
I was putting the carb to my '79 GL1000 back together today and noticed this:
DSCN2024 by Dr. Frankenstein1, on Flickr
The opening you see is me putting a little pressure on the button to make it rise, and the red dot is so I can easily identify the faulty cap - here it is without the slight pressure on it - it's a pretty clean crack:
DSCN2026 by Dr. Frankenstein1, on Flickr
Is there a fix for this that doesn't take a lathe and other equipment I don't have...? I read in here that Pistol Pete has died, and his son may have shut down the rest of his former services including button replacement...I also read that some epoxy can solve the problem too.
DSCN2024 by Dr. Frankenstein1, on Flickr
The opening you see is me putting a little pressure on the button to make it rise, and the red dot is so I can easily identify the faulty cap - here it is without the slight pressure on it - it's a pretty clean crack:
DSCN2026 by Dr. Frankenstein1, on Flickr
Is there a fix for this that doesn't take a lathe and other equipment I don't have...? I read in here that Pistol Pete has died, and his son may have shut down the rest of his former services including button replacement...I also read that some epoxy can solve the problem too.
- pidjones
- SUPER BIKER!!!!
- Posts: 3238
- Joined: Wed May 22, 2013 4:06 pm
- Location: East TN
Re: Carb Cap Crisis
Honest, I'd try super glue making sure not to get any in the port.
"Love 'em all.... let God sort 'em out!"
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
- Dr. Frankenstein
- Silver Member
- Posts: 721
- Joined: Sun Nov 10, 2019 7:22 am
- Location: Charlottesville, VA
Re: Carb Cap Crisis
Would that work? I'd think the vacuum pressure would blow it out or something...
So epoxy is a viable option?
So epoxy is a viable option?
-
- Silver Member
- Posts: 701
- Joined: Sun Apr 13, 2014 10:37 pm
- Location: Cheyenne, Wyoming
Re: Carb Cap Crisis
You need new buttons. I just sent you a PM.
- pidjones
- SUPER BIKER!!!!
- Posts: 3238
- Joined: Wed May 22, 2013 4:06 pm
- Location: East TN
Re: Carb Cap Crisis
Vacuum pulls them down. They don't have to be super-strong, but the vent hole under them needs to be free. I would really trust a good super glue over epoxy for this. I have some spares, but they really should be matched to their pistons.
"Love 'em all.... let God sort 'em out!"
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
- Sidecar Bob
- Honored Life Member
- Posts: 7655
- Joined: Sun Jun 11, 2006 10:14 pm
- Location: Kawartha Lakes, Ontario
Re: Carb Cap Crisis
I wouldn't trust any glue for that. And unless you have the tooling for installing the new buttons doing that is questionable too.
Here's what I did. 11 years later the carbs are still good so I'd call it a permanent fix.
https://www.ngwclub.com/forum/viewtopic ... 87#p437087
Here's what I did. 11 years later the carbs are still good so I'd call it a permanent fix.
https://www.ngwclub.com/forum/viewtopic ... 87#p437087
Mr. Honda ('83 GL1100/Dnepr) summer How a motorcycle evolves thread
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
- Dr. Frankenstein
- Silver Member
- Posts: 721
- Joined: Sun Nov 10, 2019 7:22 am
- Location: Charlottesville, VA
Re: Carb Cap Crisis
Actually, I sent them off to CFairweather - and they came back GREAT! This guy knows his stuff:
From this - -
DSCN2026 by Dr. Frankenstein1, on Flickr
To THIS...!
DSCN2035 by Dr. Frankenstein1, on Flickr
(The 'white' on the cap there in the lower left is just light reflecting off the cap).
DSCN2037 by Dr. Frankenstein1, on Flickr
DSCN2039 by Dr. Frankenstein1, on Flickr
He does some beautiful work! The pics don't do it justice.
From this - -
DSCN2026 by Dr. Frankenstein1, on Flickr
To THIS...!
DSCN2035 by Dr. Frankenstein1, on Flickr
(The 'white' on the cap there in the lower left is just light reflecting off the cap).
DSCN2037 by Dr. Frankenstein1, on Flickr
DSCN2039 by Dr. Frankenstein1, on Flickr
He does some beautiful work! The pics don't do it justice.
- Whiskerfish
- President
- Posts: 36936
- Joined: Thu Feb 16, 2006 9:34 pm
- My Album: http://www.ngwclub.com/gallery/v/wingmans/whiskerfish/
- Location: Norfolk Va
Re: Carb Cap Crisis
WOW!!
"Agreement is not a requirement for Respect" CDR Michael Smith USN (Ret) 2017
"The book is wrong, this whole Conclusion is Fallacious" River Tam
"Yea I do dance awkwardly, and I am having more fun than you" Taylor Swift
2008 GL1800 IIIA "TH3DOG"
1984 GL1200 Standard
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
Psst. oh and by the way CHANGE YOUR BELTS!!!!
"The book is wrong, this whole Conclusion is Fallacious" River Tam
"Yea I do dance awkwardly, and I am having more fun than you" Taylor Swift
2008 GL1800 IIIA "TH3DOG"
1984 GL1200 Standard
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
Psst. oh and by the way CHANGE YOUR BELTS!!!!
- Whiskerfish
- President
- Posts: 36936
- Joined: Thu Feb 16, 2006 9:34 pm
- My Album: http://www.ngwclub.com/gallery/v/wingmans/whiskerfish/
- Location: Norfolk Va
Re: Carb Cap Crisis
The one time I saw one of those caps actually fail was due to a backfire. Popped that sucker right off. I suspect that is how most get cracked
"Agreement is not a requirement for Respect" CDR Michael Smith USN (Ret) 2017
"The book is wrong, this whole Conclusion is Fallacious" River Tam
"Yea I do dance awkwardly, and I am having more fun than you" Taylor Swift
2008 GL1800 IIIA "TH3DOG"
1984 GL1200 Standard
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
Psst. oh and by the way CHANGE YOUR BELTS!!!!
"The book is wrong, this whole Conclusion is Fallacious" River Tam
"Yea I do dance awkwardly, and I am having more fun than you" Taylor Swift
2008 GL1800 IIIA "TH3DOG"
1984 GL1200 Standard
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
Psst. oh and by the way CHANGE YOUR BELTS!!!!
- gltriker
- Honored Life Member
- Posts: 5062
- Joined: Fri Sep 24, 2010 9:11 pm
- Location: central NY State
Re: Carb Cap Crisis
agreed!Whiskerfish wrote: ↑Thu Sep 23, 2021 7:05 pm The one time I saw one of those caps actually fail was due to a backfire. Popped that sucker right off. I suspect that is how most get cracked
I spotted this *odd looking piece of something* on my garage floor in early April, 2018. Didn't know what it was or where it may have come from and left it laying there. Looked at it again and decided to set it on trike's right side floorboard.
Backing up now,
Trike had been hibernating for at least 3 months since my last attempt to start its engine on one of those unusually brief warm days, mid-Winter. May have been on New Years Day. The attempt was cut short at my wife's insistence. " It's too cold! "
The engine had been sputtering while cranking and I twisted the throttle open just to make some noise for her benefit. The engine snorted and popped several times. I felt bad that I had been so unthoughtful to the very cold engine.
Turned the key switch off, turned the fuel valve OFF and left it to resume hibernating.
April, 2018, I sat down beside trike to check its engine oil level before starting the engine . As you will note on the top of number 1 carburetor vacuum piston cap, something is amiss. hmmmmmm? I gradually recalled the snorting and popping engine event 3 months earlier and wondered if that *odd looking piece of something* on the right side floorboard actually belonged in that opening. Yep. fit perfectly.
Fortunately, the vacuum piston, itself, wasn't damaged!
Last edited by gltriker on Fri Sep 24, 2021 2:59 am, edited 5 times in total.
Cliff (74yrs )
Keep your eyes and ears open and you'll learn something new, everyday.
New users please visit our "Shop Talk" for common tips and help: <---jdvorchak
http://www.ngwclub.com/forum/page/ST
^^^^^^^click up here^^^^^
RE: a thorough fuel tank cleaning
"And your carbs will thank you. They no longer live down stream from a sewage plant." -gregforesi
"Can't see the paint when your looking thru the handlebars..........." -Oldewing
"I'd rather Ride than Shine" -RAT Me Too!!
Cliff
'75 GL1000 home built trike; http://www.ngwclub.com/forum/viewtopic.php?f=30&t=39996
October,2017 BOTM https://nakedgoldwingsclub.com/forum/page/Welcome
previous rides:
1953 H-D Servi-car, naked, 1969-1978 (serial#53G1559 committed to memory!)
1980 CB900 Custom (triked) 1997-2003 .... R.I.P.
Keep your eyes and ears open and you'll learn something new, everyday.
New users please visit our "Shop Talk" for common tips and help: <---jdvorchak
http://www.ngwclub.com/forum/page/ST
^^^^^^^click up here^^^^^
RE: a thorough fuel tank cleaning
"And your carbs will thank you. They no longer live down stream from a sewage plant." -gregforesi
"Can't see the paint when your looking thru the handlebars..........." -Oldewing
"I'd rather Ride than Shine" -RAT Me Too!!
Cliff
'75 GL1000 home built trike; http://www.ngwclub.com/forum/viewtopic.php?f=30&t=39996
October,2017 BOTM https://nakedgoldwingsclub.com/forum/page/Welcome
previous rides:
1953 H-D Servi-car, naked, 1969-1978 (serial#53G1559 committed to memory!)
1980 CB900 Custom (triked) 1997-2003 .... R.I.P.
- Dr. Frankenstein
- Silver Member
- Posts: 721
- Joined: Sun Nov 10, 2019 7:22 am
- Location: Charlottesville, VA
Re: Carb Cap Crisis
Yes, if I can get the floats set on this '78 here (with the new caps) , I want to go over the carbs on my '75 tomorrow; I still haven't explored my Really Bad Gas Mileage on the '75 yet, and I'm hoping I haven't popped one.
-
- Gold Member
- Posts: 1128
- Joined: Tue Jun 02, 2020 8:39 am
- Location: NW Indiana,
Re: Carb Cap Crisis
My .02,
I used brass plumbing caps , 3/4” I think and used 2 part epoxy to glue them in place and as mentioned above care must be taken not to slop the epoxy around. Mine have been in for 20+ years, no problem!
That said, it’s not as simple as just gluing the new brass caps in because the caps control the slide travel by how high the slide goes, by the slide center pins hitting the inside the caps, and that’s what I believe is what breaks the nylon caps when the slide pins get slammed into the nylon caps probably due to backfires.
You want the slide to fully go up into the caps w/o the diaphragm hitting the inside the cap, you want the pin to stop the slide just short of the cap top. On mine I took some time and machined the copper plumbing caps to give the same exact travel for each cap & slide. That’s what I did ! Works great !
I used brass plumbing caps , 3/4” I think and used 2 part epoxy to glue them in place and as mentioned above care must be taken not to slop the epoxy around. Mine have been in for 20+ years, no problem!
That said, it’s not as simple as just gluing the new brass caps in because the caps control the slide travel by how high the slide goes, by the slide center pins hitting the inside the caps, and that’s what I believe is what breaks the nylon caps when the slide pins get slammed into the nylon caps probably due to backfires.
You want the slide to fully go up into the caps w/o the diaphragm hitting the inside the cap, you want the pin to stop the slide just short of the cap top. On mine I took some time and machined the copper plumbing caps to give the same exact travel for each cap & slide. That’s what I did ! Works great !
Red 1976 oe owner
1976 LTD restored
1980 CBX , in the que, to fix the ignorant heavy handed owner
1981 CBX
1977 CB750 K7
2014 FJR OE owner, sold
1980 GL1100
1984 GL1200 naked
1969 CL350, in the que
1976 LTD restored
1980 CBX , in the que, to fix the ignorant heavy handed owner
1981 CBX
1977 CB750 K7
2014 FJR OE owner, sold
1980 GL1100
1984 GL1200 naked
1969 CL350, in the que
- Sidecar Bob
- Honored Life Member
- Posts: 7655
- Joined: Sun Jun 11, 2006 10:14 pm
- Location: Kawartha Lakes, Ontario
Re: Carb Cap Crisis
Keihin designed the slides so that the shafts hit the inside of the cap before the skirts hit the insides of the caps and break and I think they intended the plastic caps to be something softer than the aluminum for the shafts to hit. (Note that GL1100 and CX/GL500/650 carbs have plastic bumpers in the ends of the shafts so that their caps don't need the buttons).
I believe that the shafts bounce against the buttons steadily at wider throttle openings. Over time exposure to UV in sunlight, heat from the engine and possibly even exposure to solvents &c used for cleaning causes the plastic that the buttons are made of become brittle and the shafts constantly tapping against them eventually cause them to develop tiny cracks.
At that point a real backfire (where it fires back through the carbs, not an afterfire in the exhaust) could cause the shaft to hit hard enough to break the cap but even without any such event the constant tapping can eventually cause the tiny cracks to develop into bigger ones and eventually break the cap completely.
In my case there was no backfire involved. The bike was running well and suddenly ran poorly. There had been a lot of talk about the buttons breaking on the forum at the time so I looked at my caps and found that the button on #1 was badly cracked and the others didn't look good. I found some washers that were a perfect fit around the bumps on the buttons and epoxied them on and epoxied nickles over them to cover the tops of the buttons. It looked nice but eventually they came off. I re-glued or replaced several of them over a couple of years and I do not recall any backfires.
In at least one case I was on the way to work, moving at a fairly steady pace and it suddenly started running rough. When I stopped for fuel near work I noticed that the nickle and part of the button was missing. When I got to work I put a couple of layers of foil duct tape over it to keep dirt out and it ran almost normally on the way home. I believe the epoxy just wasn't up to the constant tapping.
Shortly after that forum member kedanno posted that he had epoxied in freeze plugs to replace his. The last time he posted on the forum he still hadn't run his and that was 2014 so we'll probably never know whether the epoxy held but I didn't trust it so I used little bolts to fasten mine and only used epoxy to fill the cracks around the freeze plugs.
My measurements indicated that there was less than 1mm between the skirt and the cap when the shaft hit the original button and I had some HDPE sheet on hand that was the right thickness to stop them at just about the same place so I added discs of HDPE inside the freeze plugs for the slides to bump against.
I believe that the shafts bounce against the buttons steadily at wider throttle openings. Over time exposure to UV in sunlight, heat from the engine and possibly even exposure to solvents &c used for cleaning causes the plastic that the buttons are made of become brittle and the shafts constantly tapping against them eventually cause them to develop tiny cracks.
At that point a real backfire (where it fires back through the carbs, not an afterfire in the exhaust) could cause the shaft to hit hard enough to break the cap but even without any such event the constant tapping can eventually cause the tiny cracks to develop into bigger ones and eventually break the cap completely.
In my case there was no backfire involved. The bike was running well and suddenly ran poorly. There had been a lot of talk about the buttons breaking on the forum at the time so I looked at my caps and found that the button on #1 was badly cracked and the others didn't look good. I found some washers that were a perfect fit around the bumps on the buttons and epoxied them on and epoxied nickles over them to cover the tops of the buttons. It looked nice but eventually they came off. I re-glued or replaced several of them over a couple of years and I do not recall any backfires.
In at least one case I was on the way to work, moving at a fairly steady pace and it suddenly started running rough. When I stopped for fuel near work I noticed that the nickle and part of the button was missing. When I got to work I put a couple of layers of foil duct tape over it to keep dirt out and it ran almost normally on the way home. I believe the epoxy just wasn't up to the constant tapping.
Shortly after that forum member kedanno posted that he had epoxied in freeze plugs to replace his. The last time he posted on the forum he still hadn't run his and that was 2014 so we'll probably never know whether the epoxy held but I didn't trust it so I used little bolts to fasten mine and only used epoxy to fill the cracks around the freeze plugs.
My measurements indicated that there was less than 1mm between the skirt and the cap when the shaft hit the original button and I had some HDPE sheet on hand that was the right thickness to stop them at just about the same place so I added discs of HDPE inside the freeze plugs for the slides to bump against.
Mr. Honda ('83 GL1100/Dnepr) summer How a motorcycle evolves thread
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
- pidjones
- SUPER BIKER!!!!
- Posts: 3238
- Joined: Wed May 22, 2013 4:06 pm
- Location: East TN
Re: Carb Cap Crisis
Remember also that the carbs original design was for a car. I don't know if the original caps were modified for the GoldWing, but the first float bowls still had vestigial fuel pump cavities.
Last edited by pidjones on Wed Oct 06, 2021 8:04 am, edited 1 time in total.
"Love 'em all.... let God sort 'em out!"
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
-
- True Blue Steel Biker
- Posts: 2314
- Joined: Wed Apr 11, 2012 10:50 am
Re: Carb Cap Crisis
1966 Honda 600 car motor. You are right pidjones!
- Attachments
-
- 6AEF22EB-DCF4-4A21-ADE0-CFB460748A76.png (1.24 MiB) Viewed 395 times
Dave
1975 GL 1000
1980 XS650
1981 ct110
1972 F7 KAW 175
2000 moby blaze 40cc
Chihuahua (Ellie)
Chihuahua #2(Blaze)
1975 GL 1000
1980 XS650
1981 ct110
1972 F7 KAW 175
2000 moby blaze 40cc
Chihuahua (Ellie)
Chihuahua #2(Blaze)
-
- Similar Topics
- Replies
- Views
- Last post
-
- 11 Replies
- 2786 Views
-
Last post by julimike54
-
- 53 Replies
- 1334 Views
-
Last post by 82aspy
-
- 1 Replies
- 522 Views
-
Last post by NCScooter