Page 3 of 8
Re: GL1000 build - soon to be Fuel Injected
Posted: Thu Feb 07, 2019 10:20 pm
by ericheath
Recent posts here give options. See Sidecarbobs post.
viewtopic.php?f=1&t=66698&start=15
Re: GL1000 build - soon to be Fuel Injected
Posted: Sun Feb 10, 2019 12:02 pm
by GT-Ron
Re: GL1000 build - soon to be Fuel Injected
Posted: Sun Feb 10, 2019 9:18 pm
by pidjones
>Ps: what is everyone using for polishing? I would like a finish thats not too shiny.<
I use sequential grades of silicon carbide paper under a lightly running water tap. And lots of elbow grease. For more polish, rouge and the buffing wheel in my drill press. Hope the spokes have not thinned too much. It is a heavy bike.
Re: GL1000 build - soon to be Fuel Injected
Posted: Sun Feb 10, 2019 9:36 pm
by Easter
Interesting project. I am along for the ride.
Re: GL1000 build - soon to be Fuel Injected
Posted: Mon Feb 11, 2019 2:15 am
by GT-Ron
pidjones wrote:>Ps: what is everyone using for polishing? I would like a finish thats not too shiny.<
I use sequential grades of silicon carbide paper under a lightly running water tap. And lots of elbow grease. For more polish, rouge and the buffing wheel in my drill press. Hope the spokes have not thinned too much. It is a heavy bike.
Thanks will try some out and see.
Ps: i dont think any metal was removed from the spokes. The brush was gentle enough to even clean the threads and the nipples still screw on fine.
Dont have a digital vernier but the regular one says the spoke diameters measure 4mm and 3mm after the step.
Re: GL1000 build - soon to be Fuel Injected
Posted: Mon Feb 11, 2019 11:49 am
by OCR
I find that a wire wheel will leave a "brushed" look without being too glossy.
Re: GL1000 build - soon to be Fuel Injected
Posted: Mon Feb 11, 2019 12:31 pm
by GT-Ron
I have nothing to compare them to but they look perfect to me for what I’m doing with the bike. There is minor pitting on the spokes from the rust it had before, but nothing you’re gonna see from 2ft+ away.
I could go after it with some autosol metal polish for a high shine but probably wont. The way i look at it i saves about $150+ towards other electronics needsd for the efi.
Re: GL1000 build - soon to be Fuel Injected
Posted: Mon Feb 11, 2019 4:45 pm
by GT-Ron
Back to the waterpump saga. It just seems like the pump is still too good to throw away right now. So i picked up a “cheap” bearing at the local bearing shop, and donated its dust seal to the ntn bearing in the water pump. I added a small amount of grease. The seal went in easily and the pump spins firmly but with no sideways play. So going to give it a go.
Also spent some more time behind the bench grinder and wire wheel. These intake tubes have close to a stainless finish so far. I like it!
Next up, getting the frame and other bits to the powdercoaters. Need to go purchase some needle nose pliers to get the driveshaft removed from the swingarm...
Re: GL1000 build - soon to be Fuel Injected
Posted: Mon Feb 11, 2019 5:17 pm
by pidjones
Needle nose for the driveshaft? You need straight external circlip pliers to remove the circlip from the slip joint end. Then it should slide right out. There is a grease seal in the end surrounding the slip joint. Use care with it as they are unobtainium.
Re: GL1000 build - soon to be Fuel Injected
Posted: Mon Feb 11, 2019 5:56 pm
by GT-Ron
Almost forgot. My one assistant testing out the kawasaki er6-n seat I thought i may make work on the goldwing...
Re: GL1000 build - soon to be Fuel Injected
Posted: Mon Feb 11, 2019 5:58 pm
by GT-Ron
pidjones wrote:Needle nose for the driveshaft? You need straight external circlip pliers to remove the circlip from the slip joint end. Then it should slide right out. There is a grease seal in the end surrounding the slip joint. Use care with it as they are unobtainium.
Thanks yes i meant circlip not needle nose. Its kinda late here
Re: GL1000 build - soon to be Fuel Injected
Posted: Tue Feb 12, 2019 3:46 pm
by GT-Ron
pidjones wrote: There is a grease seal in the end surrounding the slip joint. Use care with it as they are unobtainium.
Pidjones do you mean no 15 in this schematic?
Mine was missing when i got in there....
Just copious amounts of grease everywhere.
Re: GL1000 build - soon to be Fuel Injected
Posted: Tue Feb 12, 2019 3:48 pm
by GT-Ron
On a related note:
How can i protect the swingarm bearings while it goes in for sandblasting and powdercoating?
Or should i just leave the old ones in to take the beating (while protecting swingarm) and replace them anyways?
Re: GL1000 build - soon to be Fuel Injected
Posted: Tue Feb 12, 2019 4:28 pm
by ericheath
I think most 75’s didn’t get the grease seal.
Re: GL1000 build - soon to be Fuel Injected
Posted: Tue Feb 12, 2019 5:57 pm
by GT-Ron
Good to know thanks eric