Baker's dozen

Tips and Recommendations from Guru Mike Nixon

Moderator: Whiskerfish

Post Reply
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Baker's dozen

#1

Post by mikenixon »

Here for your viewing enjoyment is a "baker's dozen" of tips-by-pix.

Image

First, I imagine many do not know that the float pivot pin in a GL1000 is directional? Yup. It is. It does not go in this way.

Image

But it does go in this way. On all four carbs. The reason is the two holes are not the same size. Unusual for Keihin carbs and the GL1000 is the only Keihin I know of like this. Common on Mikunis however.

Image

I expect it is not universally understood that the pivot pin has a taper on one end either. But it does. Nasty-looking pin, eh? More on this later.

Image

Another gotcha here, the primary and secondary main jet o-rings. The correct ones come from only one source, as I have pointed out twice before. And it's not Honda and it is not in any kit (except, at one time at least, the Randakk kit). Using the wrong o-ring here results in the problem shown in the picture.

Image

The correct way to check float level on the GL1000. You have to avoid the notches and the only way to do that is to angle the tool. The exact placement of the tool could be a little better in this pix, but you get the idea.

Image

Another one. The dark junk on the slide is from the crankcase recirculation system. Or, Marvel Mystery Oil in the fuel. Either is a bad thing.

Image

Here we have the aircut valve and its lower two o-rings. I always lightly glue them in place because putting the carbs on and taking them off usually involves temporarily removing this valve. Don't want to lose those babies.

Image

This is the float pivot pin again, but now look at all the scaring on it. This comes from using pliers to remove the pin. Don't do that.

Image

Here is just one reason why tearing up the pin is bad news. It is one of the reasons float pivot posts snap.

Image

Here is how I repair this, by welding. The best of the handful of options to my way of thinking. Permanent.

Image

This massive corrosion is not unusual on the GL1000. The zinc construction makes these carbs very corrosion-prone. This particular example is not salvagable.

Image

However, if the corrosion is not too bad, the jet towers can be machined down to give the main jets new purchase. But only a little. The depth of the cross-drilled hole for the idle jet determines this.
User avatar
5speed
Honored Life Member
Honored Life Member
Posts: 5311
Joined: Sat Jul 11, 2015 2:37 pm
Location: Nova Scotia Canada

Re: Baker's dozen

#2

Post by 5speed »

that is a very nice stack of dimes on that pivot pin post.. anim-cheers1
User avatar
desertrefugee
SUPER BIKER!!!!
SUPER BIKER!!!!
Posts: 3947
Joined: Fri Nov 11, 2011 9:33 pm
Location: Chandler, AZ, USA

Re: Baker's dozen

#3

Post by desertrefugee »

5speed wrote: Fri Dec 04, 2020 7:55 pm that is a very nice stack of dimes on that pivot pin post.. anim-cheers1
No kidding. Definitely a professional job. I wouldn’t even attempt welding something that fine. Heck, my work would never look like that even on large items.

Nice series of tips, BTW, Mike.
User avatar
Sugs
Gold Member
Gold Member
Posts: 1069
Joined: Sun Aug 09, 2015 6:12 pm
Location: Springfield, MO

Re: Baker's dozen

#4

Post by Sugs »

Seriously, how the heck do you weld something that small?
User avatar
CYBORG
Moderator
Moderator
Posts: 24536
Joined: Mon Jan 14, 2008 12:52 pm
Location: Muskegon mich

Re: Baker's dozen

#5

Post by CYBORG »

Sugs wrote: Fri Dec 04, 2020 9:26 pm Seriously, how the heck do you weld something that small?
I always thought they were made of a metal, {pot metal}, that was almost impossible to weld.
User avatar
5speed
Honored Life Member
Honored Life Member
Posts: 5311
Joined: Sat Jul 11, 2015 2:37 pm
Location: Nova Scotia Canada

Re: Baker's dozen

#6

Post by 5speed »

Sugs wrote: Fri Dec 04, 2020 9:26 pm Seriously, how the heck do you weld something that small?
I'm wondering the same thing..that electrode must be the size of a pin..
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Baker's dozen

#7

Post by mikenixon »

It's not me doing the welding. The welder is famous in the powersports industry, Jim French in Georgia. He is well known for what he does, welder to the stars. Microwelding, he calls what he does. Wears an exotic magnifying hood, has quite a setup. And is a vintage bike enthusiast. He has welded many things for me, mostly carbs but heads also. Yes, the early carbs (pre-1978) are heavy in zinc, thus not as easy as the later better alloy. But nothing phases Jim. He has welded for me pilot screw towers, tons of float pivot posts, even an ultra-thin vintage BMW crap alloy carb.
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Baker's dozen

#8

Post by mikenixon »

Samples...

Image
Image
Image

That last picture is a Honda ST1100 pilot screw tower.
User avatar
CYBORG
Moderator
Moderator
Posts: 24536
Joined: Mon Jan 14, 2008 12:52 pm
Location: Muskegon mich

Re: Baker's dozen

#9

Post by CYBORG »

The man has skills action1 action1 action1 action1 action1
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Baker's dozen

#10

Post by mikenixon »

Yes. A valuable resource to the powersports community. And a good guy to boot.
User avatar
sgwilly
Gold Member
Gold Member
Posts: 1029
Joined: Thu Apr 26, 2007 6:43 pm
Location: Clayton, NC

Re: Baker's dozen

#11

Post by sgwilly »

When I saw that tiny, beautiful, perfect weld - for a second I thought I was looking at kittens. Brain chemistry sure is strange.
User avatar
5speed
Honored Life Member
Honored Life Member
Posts: 5311
Joined: Sat Jul 11, 2015 2:37 pm
Location: Nova Scotia Canada

Re: Baker's dozen

#12

Post by 5speed »

I'm assuming tig?
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Baker's dozen

#13

Post by mikenixon »

5speed wrote: Sat Dec 05, 2020 10:54 am I'm assuming tig?
I would think so, but I am only mildly conversant on welding tech. :)
User avatar
5speed
Honored Life Member
Honored Life Member
Posts: 5311
Joined: Sat Jul 11, 2015 2:37 pm
Location: Nova Scotia Canada

Re: Baker's dozen

#14

Post by 5speed »

mikenixon wrote: Sat Dec 05, 2020 6:43 pm
5speed wrote: Sat Dec 05, 2020 10:54 am I'm assuming tig?
I would think so, but I am only mildly conversant on welding tech. :)
I know a grinder makes my bubble gum welds look almost good. :mrgreen:
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Baker's dozen

#15

Post by mikenixon »

:)
Post Reply

Return to “Mike Nixon's Spot”