Bad u joint on my GL1000
Moderators: Whiskerfish, Forum Moderators
-
- Titanium Member
- Posts: 407
- Joined: Tue Dec 08, 2020 2:23 pm
- Location: Slaton Tx (just o/s Lubbock)
Bad u joint on my GL1000
While tearing down my '75 GL1000 for a rebuild I found that there is slack in the u joint on the final drive. What are the options for a replacement?
1975 GL1000 Restored (sold)
1983 GL1100 Custom (sold)
1976 GL1000 Project (finished and sold)
Another1976 GL1000 Project (finished and sold)
1983 GL1100 Custom (sold)
1976 GL1000 Project (finished and sold)
Another1976 GL1000 Project (finished and sold)
-
- Billet Alum. Member
- Posts: 278
- Joined: Thu Jun 07, 2018 8:30 am
Re: Bad u joint on my GL1000
I had the same situation when I got my 1000. I bought a couple of used shafts off e-bay. One for use and the other as spare. I will eventually try and replace the universal joint on the bad shaft. Milling out the stake points seems easy enough but milling in a circlip retainer groove is a little more complicated for me as I don't have a rotary table for my milling set up.
-P.
-P.
- Whiskerfish
- President
- Posts: 36850
- Joined: Thu Feb 16, 2006 9:34 pm
- My Album: http://www.ngwclub.com/gallery/v/wingmans/whiskerfish/
- Location: Norfolk Va
Re: Bad u joint on my GL1000
Many guys have explored the rebuild process with hope of being able to come up with a economical method. I have not heard of one. Apparently Honda used several different sources for these as there are 4 or 5 variations of the U Joint. A few guys have rebuilt one or two for their own personal use but none that I am aware for resale. So rebuilding your own or purchasing low mileage used are about the only options.
"Agreement is not a requirement for Respect" CDR Michael Smith USN (Ret) 2017
"The book is wrong, this whole Conclusion is Fallacious" River Tam
2008 GL1800 IIIA "TH3DOG"
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
and a whole garage full of possibilities!!
Psst. oh and by the way CHANGE YOUR BELTS!!!!
"The book is wrong, this whole Conclusion is Fallacious" River Tam
2008 GL1800 IIIA "TH3DOG"
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
and a whole garage full of possibilities!!
Psst. oh and by the way CHANGE YOUR BELTS!!!!
- pidjones
- SUPER BIKER!!!!
- Posts: 3237
- Joined: Wed May 22, 2013 4:06 pm
- Location: East TN
Re: Bad u joint on my GL1000
My Hunley build was bad sloppy. Found a swingarm with driveshaft on ebay and made an offer for just the driveshaft. Seller accepted and the joint is in great shape. Actually, staking in a new joint wouldn't be that hard. Even tack welds. No need to machine a snap ring groove.
"Love 'em all.... let God sort 'em out!"
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
- ericheath
- Honored Life Member
- Posts: 9580
- Joined: Wed Jul 29, 2009 11:20 am
- Location: Winnipeg, Manituba
Re: Bad u joint on my GL1000
Sandy has done it using a joint from a steering sector or PTO shaft of a large truck. (Freight liner???) Some have poopoo’d the idea because it’s not in the design to spin at higher rpm, but he’s put many miles on it.
It fits, and he tacked it in place. I think we’re nearing the point that this may be the only option.
It fits, and he tacked it in place. I think we’re nearing the point that this may be the only option.
Whatever I suggest here should be given ample time for a moderator to delicately correct. I apologize in advance.
77 WING, 1200 engine with 77 heads, cams, gl1100 foot pegs, Magna V65 front end, 764A carbs, [-gone Suzuki M109 monoshock--, replaced with gl1100 shocks] gl 1200 swing arm, gl1500 final drive, wheel and rear brakes Valkyrie seat, Meanstreak tank, Sportster pipes, Power Arc ignition off crank.
77 Wing. black
83 Wing, in pieces
"Continuing education is important even if the subject matter is fairly useless (as in this case)."---Greg Foresi
77 WING, 1200 engine with 77 heads, cams, gl1100 foot pegs, Magna V65 front end, 764A carbs, [-gone Suzuki M109 monoshock--, replaced with gl1100 shocks] gl 1200 swing arm, gl1500 final drive, wheel and rear brakes Valkyrie seat, Meanstreak tank, Sportster pipes, Power Arc ignition off crank.
77 Wing. black
83 Wing, in pieces
"Continuing education is important even if the subject matter is fairly useless (as in this case)."---Greg Foresi
- ericheath
- Honored Life Member
- Posts: 9580
- Joined: Wed Jul 29, 2009 11:20 am
- Location: Winnipeg, Manituba
Re: Bad u joint on my GL1000
This U joint seems to work.
neapco u joint 1-0475
He tacked and then epoxied it in place. I have some pics somewhere.
neapco u joint 1-0475
He tacked and then epoxied it in place. I have some pics somewhere.
Whatever I suggest here should be given ample time for a moderator to delicately correct. I apologize in advance.
77 WING, 1200 engine with 77 heads, cams, gl1100 foot pegs, Magna V65 front end, 764A carbs, [-gone Suzuki M109 monoshock--, replaced with gl1100 shocks] gl 1200 swing arm, gl1500 final drive, wheel and rear brakes Valkyrie seat, Meanstreak tank, Sportster pipes, Power Arc ignition off crank.
77 Wing. black
83 Wing, in pieces
"Continuing education is important even if the subject matter is fairly useless (as in this case)."---Greg Foresi
77 WING, 1200 engine with 77 heads, cams, gl1100 foot pegs, Magna V65 front end, 764A carbs, [-gone Suzuki M109 monoshock--, replaced with gl1100 shocks] gl 1200 swing arm, gl1500 final drive, wheel and rear brakes Valkyrie seat, Meanstreak tank, Sportster pipes, Power Arc ignition off crank.
77 Wing. black
83 Wing, in pieces
"Continuing education is important even if the subject matter is fairly useless (as in this case)."---Greg Foresi
-
- Titanium Member
- Posts: 407
- Joined: Tue Dec 08, 2020 2:23 pm
- Location: Slaton Tx (just o/s Lubbock)
Re: Bad u joint on my GL1000
The problem I see to replacing the joint is getting it centered in the yokes. And staking it without some kind of a fixture might cause the cups to go in too tight and bind on the cross shaft. I do have a lathe I can chuck it up in and put a dial indicator on it. I may give it a try.
1975 GL1000 Restored (sold)
1983 GL1100 Custom (sold)
1976 GL1000 Project (finished and sold)
Another1976 GL1000 Project (finished and sold)
1983 GL1100 Custom (sold)
1976 GL1000 Project (finished and sold)
Another1976 GL1000 Project (finished and sold)
-
- Honored Life Member
- Posts: 4646
- Joined: Wed Jun 28, 2006 2:52 pm
- Location: up by the Canadian border in WA state
Re: Bad u joint on my GL1000
MikeNTexas wrote: ↑Sat Dec 19, 2020 7:32 pm The problem I see to replacing the joint is getting it centered in the yokes. And staking it without some kind of a fixture might cause the cups to go in too tight and bind on the cross shaft. I do have a lathe I can chuck it up in and put a dial indicator on it. I may give it a try.
Pls keep us updated on how this pans out.
Color me Interested.
sorta bulldogged custom 1978 GL1000 - "geekster"
full Vetter dress 1979 GL1000 - "Barge" (currently down)
1986 1200 Aspencade - "Heart of Gold" - daily rider
1990 1500 Aspencade - It's ALIVE! but very, very naked. not in a good way.
1978 for $100 - project in worx
1978 from a previous member here - taking up space
my original '79 bought in '91 - replacing engine (eventually, maybe someday)
H2G2=42
A competent and self-confident person is incapable of jealousy in anything. Jealousy is invariably a symptom of neurotic insecurity. ~ Robert A. Heinlein
The good thing about science is that it's true whether or not you believe in it. ~ Neil deGrasse Tyson
full Vetter dress 1979 GL1000 - "Barge" (currently down)
1986 1200 Aspencade - "Heart of Gold" - daily rider
1990 1500 Aspencade - It's ALIVE! but very, very naked. not in a good way.
1978 for $100 - project in worx
1978 from a previous member here - taking up space
my original '79 bought in '91 - replacing engine (eventually, maybe someday)
H2G2=42
A competent and self-confident person is incapable of jealousy in anything. Jealousy is invariably a symptom of neurotic insecurity. ~ Robert A. Heinlein
The good thing about science is that it's true whether or not you believe in it. ~ Neil deGrasse Tyson
-
- Silver Member
- Posts: 654
- Joined: Fri May 26, 2017 11:07 am
Re: Bad u joint on my GL1000
I had a hybrid driveshaft made for my 1200-into-1000-with-1100-swingarm project. Without actually checking the number, I think I used the Neapco joint Eric mentions. Since the originals were staked, I took the parts to a machine shop and they cut the snapring retainer grooves into the yokes and assembled it all. The machinist was initially a little unsure whether he'd be able to cut those small grooves, but it came out good. So far; don't have many miles on it yet.
Not that it applies here, but while I could press the old crosses out of the 1000 yoke, the 1100 yoke had more meat in the front piece and there wasn't enough room to clear, so I had to saw it apart. Which is probably one reason why these are considered unrebuildable.
Not that it applies here, but while I could press the old crosses out of the 1000 yoke, the 1100 yoke had more meat in the front piece and there wasn't enough room to clear, so I had to saw it apart. Which is probably one reason why these are considered unrebuildable.
- gltriker
- Honored Life Member
- Posts: 5053
- Joined: Fri Sep 24, 2010 9:11 pm
- Location: central NY State
Re: Bad u joint on my GL1000
check this topic for swingarm/driveshaft
https://ngwclub.com/forum/viewtopic.php?f=6&t=75778
https://ngwclub.com/forum/viewtopic.php?f=6&t=75778
Cliff (74yrs )
Keep your eyes and ears open and you'll learn something new, everyday.
New users please visit our "Shop Talk" for common tips and help: <---jdvorchak
http://www.ngwclub.com/forum/page/ST
^^^^^^^click up here^^^^^
RE: a thorough fuel tank cleaning
"And your carbs will thank you. They no longer live down stream from a sewage plant." -gregforesi
"Can't see the paint when your looking thru the handlebars..........." -Oldewing
"I'd rather Ride than Shine" -RAT Me Too!!
Cliff
'75 GL1000 home built trike; http://www.ngwclub.com/forum/viewtopic.php?f=30&t=39996
October,2017 BOTM https://nakedgoldwingsclub.com/forum/page/Welcome
previous rides:
1953 H-D Servi-car, naked, 1969-1978 (serial#53G1559 committed to memory!)
1980 CB900 Custom (triked) 1997-2003 .... R.I.P.
Keep your eyes and ears open and you'll learn something new, everyday.
New users please visit our "Shop Talk" for common tips and help: <---jdvorchak
http://www.ngwclub.com/forum/page/ST
^^^^^^^click up here^^^^^
RE: a thorough fuel tank cleaning
"And your carbs will thank you. They no longer live down stream from a sewage plant." -gregforesi
"Can't see the paint when your looking thru the handlebars..........." -Oldewing
"I'd rather Ride than Shine" -RAT Me Too!!
Cliff
'75 GL1000 home built trike; http://www.ngwclub.com/forum/viewtopic.php?f=30&t=39996
October,2017 BOTM https://nakedgoldwingsclub.com/forum/page/Welcome
previous rides:
1953 H-D Servi-car, naked, 1969-1978 (serial#53G1559 committed to memory!)
1980 CB900 Custom (triked) 1997-2003 .... R.I.P.
- Sidecar Bob
- Honored Life Member
- Posts: 7631
- Joined: Sun Jun 11, 2006 10:14 pm
- Location: Kawartha Lakes, Ontario
Re: Bad u joint on my GL1000
FWIW, the u-joint on my first 'Wing let go on me as I was half way around a highway exit ramp about 3/4 of the way home after a long day out. This was in the early '90s (before cellphones) and it was about midnight in the middle of nowhere but I pushed it to a house with a light on and asked to use the phone.
The yokes were so badly worn that the cross fell out. At that time Honda still had new ones in stock and they didn't cost much more than a decent chain & sprockets set for a chain drive bike would have. This was the first bike I had with a u-joint and when I had it going again I realized that what I had thought was a normal noise wasn't there anymore.
I now know to look for play in the u-joint as part of routine maintenance but I've never found another that was at all loose.
The yokes were so badly worn that the cross fell out. At that time Honda still had new ones in stock and they didn't cost much more than a decent chain & sprockets set for a chain drive bike would have. This was the first bike I had with a u-joint and when I had it going again I realized that what I had thought was a normal noise wasn't there anymore.
I now know to look for play in the u-joint as part of routine maintenance but I've never found another that was at all loose.
Mr. Honda ('83 GL1100/Dnepr) summer How a motorcycle evolves thread
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
- 5speed
- Honored Life Member
- Posts: 5311
- Joined: Sat Jul 11, 2015 2:37 pm
- Location: Nova Scotia Canada
Re: Bad u joint on my GL1000
does the 1100 suffer from the same unobtanium u joint as the 1000?
1982 1100 standard. (sold)
1986 Yamaha FJ1200
2000 Yamaha Roadstar
1976 GoldWing. running but not on the road
1978 Goldwing. future cafe project.
2019 Can-Am ryker (boss's new ride)
2002 Shadow American Classic(sold)
1983 Shadow 500. (sold)
1986 Yamaha FJ1200
2000 Yamaha Roadstar
1976 GoldWing. running but not on the road
1978 Goldwing. future cafe project.
2019 Can-Am ryker (boss's new ride)
2002 Shadow American Classic(sold)
1983 Shadow 500. (sold)
- Sidecar Bob
- Honored Life Member
- Posts: 7631
- Joined: Sun Jun 11, 2006 10:14 pm
- Location: Kawartha Lakes, Ontario
Re: Bad u joint on my GL1000
I don't know about the cross and bearings but the shafts are different lengths.
Mr. Honda ('83 GL1100/Dnepr) summer How a motorcycle evolves thread
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
- pidjones
- SUPER BIKER!!!!
- Posts: 3237
- Joined: Wed May 22, 2013 4:06 pm
- Location: East TN
Re: Bad u joint on my GL1000
Another option to consider for locating a new joint would be some kind of epoxy. Some cars and trucks use a thermoplastic blob to hold theirs in place, but it can be melted out and there is a snap ring groove for rebuilds. Don't know which I would trust more, though - snap ring or epoxy?
"Love 'em all.... let God sort 'em out!"
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
Ex 2006 GL1800 - the Black Pearl SOLD! to make room for:
2021 Can-Am Spyder RT Limited Dark Chalk Metallic
1975 Red GL1000 project - ex Pistol Pete project
1972 Triumph T150V Trident rescue - finished and FOR SALE!
1976 Yamaha RD400c
1978 GL1000 with '75 engine - the Hunley
Ex 1978 GL1000
Ex 1979 GL1000
Ex '79 CB750F rat bike
Ex '86 SEi
Ex '77 GL1000
Ex '76 RD400
Ex '72 Penton 125 set up for flat track
Ex '73 RD250
Ex '68 TR6C - chopped
- 5speed
- Honored Life Member
- Posts: 5311
- Joined: Sat Jul 11, 2015 2:37 pm
- Location: Nova Scotia Canada
Re: Bad u joint on my GL1000
I changed the u joints in my 86 IROC 2 years ago and they were the original ones held in with the plastic retainers..pidjones wrote: ↑Sun Dec 27, 2020 4:40 pm Another option to consider for locating a new joint would be some kind of epoxy. Some cars and trucks use a thermoplastic blob to hold theirs in place, but it can be melted out and there is a snap ring groove for rebuilds. Don't know which I would trust more, though - snap ring or epoxy?
I wonder if you would throw the drive shaft out of balance if the globs of epoxy were different weights..
1982 1100 standard. (sold)
1986 Yamaha FJ1200
2000 Yamaha Roadstar
1976 GoldWing. running but not on the road
1978 Goldwing. future cafe project.
2019 Can-Am ryker (boss's new ride)
2002 Shadow American Classic(sold)
1983 Shadow 500. (sold)
1986 Yamaha FJ1200
2000 Yamaha Roadstar
1976 GoldWing. running but not on the road
1978 Goldwing. future cafe project.
2019 Can-Am ryker (boss's new ride)
2002 Shadow American Classic(sold)
1983 Shadow 500. (sold)
-
- Similar Topics
- Replies
- Views
- Last post
-
- 21 Replies
- 1448 Views
-
Last post by redglbx
-
- 12 Replies
- 433 Views
-
Last post by Whiskerfish
-
- 4 Replies
- 192 Views
-
Last post by ericheath
-
- 8 Replies
- 298 Views
-
Last post by Shadowjack