BUILD A CUSTOM SISSYBAR BRACKET Sunnbobb's How-to

From basic novice to the hard core cutomizing. Sharing tips, tricks and knowledge. Feel
free to ask question or give us your "2 cents".

Moderators: sunnbobb, Neil, Forum Moderators

Post Reply
User avatar
sunnbobb
Facebook Admin
Facebook Admin
Posts: 21272
Joined: Thu Jan 10, 2008 4:09 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/sunnbobb/
Location: LaConner, WA

BUILD A CUSTOM SISSYBAR BRACKET Sunnbobb's How-to

#1

Post by sunnbobb »

Hi boys and girls! Today I thought I would demonstrate how to build a simple custom bracket. In this example, I am constructing a bracket for an after market sissybar, however, the simple techniques shown in the following demonstration could be applied to many other types of brackets as well.

The sissybar will be mounted to the rear frame rails of a 78 GL1000. The standard outside dimension of the 78 GL1000 frame is 8 3/4" +/- 1/8". It just so happens that sissybars made for Harleys by Kuryakyn (part number 1587) have an outside mounting dimension of 8 3/4".

The specs on the sissybar are: 8-3/4 in. outside mounting dimension, .55 in. square stock mounting and 1-1/4 in. mounting hole spacing.

To mount the sissybar, you can buy a bracket system or fabricate one. I chose the latter. I went over to my favorite scrap metal yard and scored a 2 foot square piece of 7/32" for 6 bucks.

After designing the part and transferring it to the aluminum stock, I cut the rough brackets using a saber saw with a blade designed for thick metal. It cut like butter.

The next step was to take the parts and run them through the grinder to get everything smooth. Then, putting a small abrasive stone on a Dremel, I lightly rounded the edges.

At this point, I drilled the holes for both the sissybar mount and the frame mount.

Finishing consisted of 400 grit sand paper, followed by a 600 wet sand. The part was then taken over to the buffer and buffed to a mirror finish.

Finally, I drilled an extra hole in the frame rail and mounted the brackets and bar.

Using these simple steps, a person could make a bracket that extends all the way to the shock and adds a little design flair if they wished.

That's it for today, and remember, if your day doesn't shine, use a better polish!

Cutting the parts out of thick aluminum stock

Image


Buffing the part

Image


Drilling extra hole in frame. (be sure to seal the hole to insure it doesnt rust in the future)

Image


Bracket mounted to frame

Image

Bracket closeup prior to finishing

Image
I found the end of the internet

---- Bradshaw Bikes custom polishing for your wing. Visit us on facebook!

1978 Learning Experience
1980 County Road Hauler "Brain Damage"
1978 Cafe Custom Gl1000 "Vyper"
1977 Bulldog Inspired "Vaincre"
1981 Street Fighter GL1100 "No Quarter"
1983 Supercharged Street Drag "Anubis" (in worx)
1983 gl1100 mint restoration "Kristen"
1985 Aspencade..pondering.
User avatar
peteybug
Silver Member
Silver Member
Posts: 787
Joined: Sun Feb 10, 2008 2:20 pm
Location: northern new york

#2

Post by peteybug »

Nice job sunnbobb looks great. Just so you know if you have a router for woodworking aluminum is soft so you could do your round over's with a round over bit. ;)
love new ideas for old wing's. AS I have three and am always working on them

[img]http://i253.photobucket.com/albums/hh55/peteybug8/motorcycle040-1.jpg[/img][img]http://i253.photobucket.com/albums/hh55/peteybug8/motorcycle037-1-1.jpg[/img][img]http://i253.photobucket.com/albums/hh55/peteybug8/3%20wings/Townworkandbikes036-1.jpg[/img]
User avatar
sunnbobb
Facebook Admin
Facebook Admin
Posts: 21272
Joined: Thu Jan 10, 2008 4:09 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/sunnbobb/
Location: LaConner, WA

#3

Post by sunnbobb »

Thanks Petey, I wondered but never tried it. I have boatloads of woodworking tools looking for other purposes!

Sunny
I found the end of the internet

---- Bradshaw Bikes custom polishing for your wing. Visit us on facebook!

1978 Learning Experience
1980 County Road Hauler "Brain Damage"
1978 Cafe Custom Gl1000 "Vyper"
1977 Bulldog Inspired "Vaincre"
1981 Street Fighter GL1100 "No Quarter"
1983 Supercharged Street Drag "Anubis" (in worx)
1983 gl1100 mint restoration "Kristen"
1985 Aspencade..pondering.
User avatar
Zryder
True Blue Steel Biker
True Blue Steel Biker
Posts: 2954
Joined: Tue Dec 14, 2004 2:12 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/zryder/

#4

Post by Zryder »

Yes . very nice work sunnbobb tumb2


Zryder
1982 GL 1100 std. Custom Image
To my album ; http://www.ngwclub.com/gallery/v/wingmans/zryder/
User avatar
MesaMike
Zinc Member
Zinc Member
Posts: 40
Joined: Mon Dec 01, 2008 10:32 pm
Location: Mesa Arizona

Bobber Sissy Bar

#5

Post by MesaMike »

I've got a 76 bobber that I would like to stretch the seat all the way to the end of the fender, not much room but squeeze in tight baby, and put a 3 or 4 inch sissy bar there to be able to bungee stuff down and not worrying about it sliding off. I just saw the pictures of making one, but don't have the tools. Any ideas?

Any more pictures out there of short sissy bars?????

Thanks
MesaMike
1976 gl1000 bobber/mix bike
Running, repairing after wreck.
User avatar
sunnbobb
Facebook Admin
Facebook Admin
Posts: 21272
Joined: Thu Jan 10, 2008 4:09 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/sunnbobb/
Location: LaConner, WA

#6

Post by sunnbobb »

i can whip you up a bracket...
I found the end of the internet

---- Bradshaw Bikes custom polishing for your wing. Visit us on facebook!

1978 Learning Experience
1980 County Road Hauler "Brain Damage"
1978 Cafe Custom Gl1000 "Vyper"
1977 Bulldog Inspired "Vaincre"
1981 Street Fighter GL1100 "No Quarter"
1983 Supercharged Street Drag "Anubis" (in worx)
1983 gl1100 mint restoration "Kristen"
1985 Aspencade..pondering.
User avatar
Roady
Member Relations &_Graphics
Member Relations &_Graphics
Posts: 11957
Joined: Wed Jun 20, 2007 2:35 pm
Location: Port St. John, FL

#7

Post by Roady »

Nice bracketry there. How did I miss this thread?

Oh, I get it ... it's not on ShopTalk yet.
User avatar
MesaMike
Zinc Member
Zinc Member
Posts: 40
Joined: Mon Dec 01, 2008 10:32 pm
Location: Mesa Arizona

Sissy Bar Brackets

#8

Post by MesaMike »

Hope this works, trying to insert a picture of the back of my 76. I know, I know the seat looks like crap and feels like it. That's another project. So I need a bracket that lines up with the rear edge of the bike. Black preferred.


MesaMike

Image

sunnbobb, how can I get hold of you? Still new to this!
MesaMike
1976 gl1000 bobber/mix bike
Running, repairing after wreck.
User avatar
Roady
Member Relations &_Graphics
Member Relations &_Graphics
Posts: 11957
Joined: Wed Jun 20, 2007 2:35 pm
Location: Port St. John, FL

#9

Post by Roady »

Just click the PM button at the bottom of one of his posts.

Write him a note and he'll get back with ya.
Slagg50
Lead Member
Lead Member
Posts: 5
Joined: Tue Mar 03, 2009 12:43 am
Location: Kansas City

#10

Post by Slagg50 »

I was looking at your gallery and noticed that when you got your bike, it came with a passenger backrest/rack setup.
Is that a stock piece, aftermarket?
Do you know where a guy could get one?

Thanks,
Keith
'82 GL1100
User avatar
sunnbobb
Facebook Admin
Facebook Admin
Posts: 21272
Joined: Thu Jan 10, 2008 4:09 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/sunnbobb/
Location: LaConner, WA

#11

Post by sunnbobb »

Ya Hey Keith, I think all it had was the grab rail and it was stock. I sold it for waaaay less than I later found out they were worth! LOL Good luck finding one!
I found the end of the internet

---- Bradshaw Bikes custom polishing for your wing. Visit us on facebook!

1978 Learning Experience
1980 County Road Hauler "Brain Damage"
1978 Cafe Custom Gl1000 "Vyper"
1977 Bulldog Inspired "Vaincre"
1981 Street Fighter GL1100 "No Quarter"
1983 Supercharged Street Drag "Anubis" (in worx)
1983 gl1100 mint restoration "Kristen"
1985 Aspencade..pondering.
User avatar
partpusher
Tin Member
Tin Member
Posts: 11
Joined: Sun Aug 01, 2010 2:34 pm
Location: roseburg, oregon

Re: BUILD A CUSTOM SISSYBAR BRACKET Sunnbobb's How-to

#12

Post by partpusher »

hey, i found out when you take the factory trunk/seatback off, the rear fender tends to lose support.
if you make a few changes here/there you can use a chrome super sport fender which has support built in.
you can get a rear rail from a standard such as this one on ebay now:
http://cgi.ebay.com/ebaymotors/ws/eBayI ... K:MEWAX:IT

now you take all the chrome guards/bars off the rear and just use this and a sissy like the one so nicely demonstrated above.

i still thought it was a giant morass of chrome, so i (LUCKILY) found this tidy little biddy instead:
User avatar
sunnbobb
Facebook Admin
Facebook Admin
Posts: 21272
Joined: Thu Jan 10, 2008 4:09 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/sunnbobb/
Location: LaConner, WA

Re: BUILD A CUSTOM SISSYBAR BRACKET Sunnbobb's How-to

#13

Post by sunnbobb »

The photo in the auction appears to be a grab rail. I see you are a coug too. Welcome to NGW, glad to see another member from the Salish Sea.
I found the end of the internet

---- Bradshaw Bikes custom polishing for your wing. Visit us on facebook!

1978 Learning Experience
1980 County Road Hauler "Brain Damage"
1978 Cafe Custom Gl1000 "Vyper"
1977 Bulldog Inspired "Vaincre"
1981 Street Fighter GL1100 "No Quarter"
1983 Supercharged Street Drag "Anubis" (in worx)
1983 gl1100 mint restoration "Kristen"
1985 Aspencade..pondering.
User avatar
partpusher
Tin Member
Tin Member
Posts: 11
Joined: Sun Aug 01, 2010 2:34 pm
Location: roseburg, oregon

Re: BUILD A CUSTOM SISSYBAR BRACKET Sunnbobb's How-to

#14

Post by partpusher »

thanks sunbobb. the nice thing about a wing is i can take a weekend and visit my old friends in wally world soon.
i'm working up a bio now. and im gonna go with photobucket.
stay 'tuned'
tim
User avatar
partpusher
Tin Member
Tin Member
Posts: 11
Joined: Sun Aug 01, 2010 2:34 pm
Location: roseburg, oregon

Re: BUILD A CUSTOM SISSYBAR BRACKET Sunnbobb's How-to

#15

Post by partpusher »

btw, that thing in the auction, a grab rail. . .that would provide plenty of support to the stock fender when going naked wouldnt it?
it just seemed real bulky-looking and chromey compared to the hogtail. . . . maybe overkill
Post Reply
  • Similar Topics
    Replies
    Views
    Last post

Return to “GoldWing UnderGround CustomiZing”