1976 GL1000 with LTD wheels- year long project

A forum for stories, pics and updates of your resto's. Be it a barn find, Grampas hand me down or a bike being brought back to it's former glory.If you are restoring it, show us your stuff!

Moderators: Brant, Sagebrush, Forum Moderators

Post Reply
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

1976 GL1000 with LTD wheels- year long project

#1

Post by flyin900 »

I am posting a few of the take apart pictures of various parts of the bike, since I didn't take a picture of the whole bike initially. This bike has been an adventure in patience and frustration at every turn. I restored a 1980 GL1100 Standard about 5 years ago and while that too was somewhat of a challenge this bike the 1976 GL1000 has set a new record.

I had to replace the water pump with a new one after a failed rebuild of the original and more than a few attempts to find the problem with my rebuild work. Then chasing water leaks in the front transmission cover and thermostat housing and the temp sensor areas. The left cylinder head had a micro crack down in the oil drain back port that I missed initially leading to an oil leak, possibly when the head was decked at the machine shop that required a replacement head. The carb rebuild and starter clutch rebuild all were a learning experience, along with repairing the main wiring harness from PO's who added various accessories and butchered the harness and connectors. After reading about others adventures on the forums it seems with these 40+ year old Goldwings most of this is par for the course.

This bike had sat for 12+ years in a garage fortunately, yet was in terrible shape overall even if the motor was still free on the kickstarter. It sported a set of the LTD edition gold spoked DID rims which frankly became my main interest, since I thought that worse case senerio I could recover my initial purchase price on the rims alone if needed. It also came with a brand new starter clutch assembly and other Honda parts as the owner indicated the starter clutch was shot.



wiring harness
P1030484.JPG
P1030484.JPG (143.77 KiB) Viewed 782 times
gas tank area non stock seat mods by PO
P1030451.JPG
P1030451.JPG (135.59 KiB) Viewed 782 times
timing cover missing bolt
P1030491.JPG
P1030491.JPG (120.4 KiB) Viewed 782 times
headlight wiring-removed every scotch lock and soldered and heat shrinked every damaged wire
P1030522.JPG
P1030522.JPG (136.23 KiB) Viewed 782 times
starter clutch gear drive - needed replacing from rust pitting on roller contact surface
P1030698.JPG
P1030698.JPG (185.83 KiB) Viewed 782 times
Last edited by flyin900 on Thu Apr 06, 2017 10:07 pm, edited 11 times in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#2

Post by flyin900 »

The bike was in need of a complete teardown of both the motor and the frame and brakes to get it to a place where a rebuild and repaint could start to take place. I found a cylinder that had some pitting from an exhaust valve being open and these motors are more prone to moisture getting into the bores because of the flat engine design. The old starter clutch needed to be removed from the rotor housing and it took a bit of work and heat to get the old part free from the rotor and then a new starter clutch housing and new rollers, pins and springs were installed.
There was nothing in decent shape on the bike and the more I got into the teardown and restoration in hindsight the bike probably should have been parted out. The cylinder pitting damage was a case of hand sanding and reworking the area to get it decent enough to not damage the rings in the piston.

rear brake caliper-leaky seals and fluid damaged pads
P1030566.JPG
P1030566.JPG (113.85 KiB) Viewed 781 times
starter clutch- lots of rusty corrosion and roller pitting-a new part installed in overhaul
P1030701.JPG
P1030701.JPG (124.26 KiB) Viewed 781 times
cylinder damage- couldn't get it totally cleaned up
P1040005.JPG
P1040005.JPG (105.13 KiB) Viewed 781 times
rear end- some gouges that did polish out eventually
P1030612.JPG
P1030612.JPG (127.31 KiB) Viewed 781 times
shelter electrical- the 7 volt reg in bottom of pic was shot.
P1030590.JPG
P1030590.JPG (130.16 KiB) Viewed 781 times
Last edited by flyin900 on Sun Dec 25, 2016 12:42 am, edited 11 times in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#3

Post by flyin900 »

After the teardown I was able to start with the cleaning and repainting of larger parts such as the frame and associated smaller parts that hold the bike together. I cleaned the swing arm bearings and seals as they were solid from old grease and I needed a replacement drive shaft, as the original had too much play in the U joints. The front forks were rebuilt, repolished lowers and all new wheel bearings in the wheels along with new tires.
I put in a new clutch pack with mother Honda metal and EBC fibre plates and new Honda springs and a complete new starter clutch assembly. I needed to replace the starter clutch gear assembly that the rollers grab onto as the surface was severely pitted on the original part. The starter itself was fully rebuilt with all new internal key parts. I did the clutch scavanger oil pump modification while in there too and replace the output bearing in the rear case that supports the output shaft where it exits the case. All rear case seals were replaced with new and the kick starter assembly was taken apart and cleaned up to get it working correctly again, as it wouldn't return after being kicked down.
The front of the motor had new tensioner rollers and new timing belts, water pump and all new sensors for the water temperature housings. New hoses and thermostat and all new seals in the front housing/transmission cover. The carbs were rebuilt with Randakk's kit plus the throttle shaft felts were replaced with new and that caused some further work to get the throttle plates back to factory settings.
The gas tank was a mess inside of really old gas that took ages to get clean, yet the payoff was a spotless rust free tank under all that "protective coating" :-D I rebuilt and refreshed all the switches by taking them apart and cleaning and repainting the housings, plus the speedo and tach were also taken apart and cleaned and lubed.

switch before
image.jpeg
image.jpeg (138.47 KiB) Viewed 709 times
switch after
P1030970.JPG
P1030970.JPG (73.95 KiB) Viewed 778 times
rear case rebuild progress
P1030988.JPG
P1030988.JPG (128.88 KiB) Viewed 778 times
awaiting heads return
P1040044.JPG
P1040044.JPG (115.71 KiB) Viewed 778 times
motor ready for install
P1040070.JPG
P1040070.JPG (102.75 KiB) Viewed 778 times
The heads were all redone with a valve job and new stem seals and as noted the heads were decked too. I later found one had an issue with a crack down in the oil return port when I got the bike running initially. I tried to fix the oil leak around the 6mm bolt with the putty style metal repair on both the outside and inside of the head. It didn't work and while a weld job may have repaired it; I opted for a replacement head as I was feeling snake bitten with this project. :( I did also do the rocker arm fix noted in the Tech section of the forum from Old Fogey and he was very helpful when I initally got the bike running in helping me correct the carb throttle plate issue that I had after replacing the throttle shaft felts when I did the carb rebuild.
Last edited by flyin900 on Sat Feb 04, 2017 11:12 pm, edited 15 times in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#4

Post by flyin900 »

The brakes have all new parts inside the calipers including pistons, as there was some very minor pitting on the original pistons, just enough to start weepy leaks on the front calipers after just a seal replacement initially. I was able to find some NOS early style Vesrah brake pads here locally that a seller had for sale. I cleaned and polished every aluminum part on the bike including the scratched up part that holds the rear shock to the pumpkin drive. I used the "Sirus Consolidated" new OEM style rubber brake hose kit, since it includes all front and the rear pieces plus the speciality rear rubber caliper hose.
I used a DupliColor lacquer called "Molten Metallic Red" for the main colour on the bike panels and a stock graphics kit where I altered the pin stripes on the false tank to a single stripe. All new hardware was purchased to rebuild the side cover locking screws and I added/modified the footrests from a Honda VTX onto the GL1000 front peg mounts and GL1200 standard rear passenger pegs.
The headlight is from a 1979 CX500 which uses the same bucket as the 76 GL1000, yet the light fixture is a replaceable 55 watt H4 bulb instead of the sealed beam 40W original to the stock bike. I have a GL1000 LTD seat with the bike and there are a few other LTD parts on the bike itself, yet the serial numbers on the frame and motor indicate it isn't a LTD edition model. It actually was originally the Sulfur Yellow colour, which I now understand was a rare colour for the bike too. I have added a Corbin Touring saddle and the back rest that will be my starting riding gear once I get this on the road next spring. This required adding some era correct pull back pieces to the top bridge/handle bars to assist my arm reach to use the Corbin back rest correctly.

bike inside fall 2015
P1030979.JPG
P1030979.JPG (140.02 KiB) Viewed 774 times
gauge cluster after refresh
P1030992.JPG
P1030992.JPG (93.47 KiB) Viewed 774 times
bike in garage recently
P1040330.JPG
P1040330.JPG (106.21 KiB) Viewed 774 times
Some gold accents to highlight the LTD gold wheels.
P1040331.JPG
P1040331.JPG (153.6 KiB) Viewed 774 times
latest progress awaiting muffler install
P1040329.JPG
P1040329.JPG (141.78 KiB) Viewed 774 times
The stock Honda 'horseshoe' muffler required new front inlet pipes to be welded onto the old broken off stubs, so I used the short 4" exhaust flange adaptors available from auto parts stores. I found two that had the correct sizing to fit over the muffler section stubs for welding a solid repair and expanded larger on the front to accept the exhaust header and the sealing gasket.
Last edited by flyin900 on Sat Apr 01, 2017 9:10 am, edited 15 times in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#5

Post by flyin900 »

The bike is now finished for the year and I was able to get the appraisal on it a few days ago before the dusting of snow here recently. I have taken quite a few finished pictures of the bike showing a complete interior of the shelter work to start with and ending with various shots of the bike with both the stock Honda LTD seat that came with the bike and an aftermarket Corbin seat that I purchased locally with the back rest.
I am running a set of stock CB450 Black Bomber double sprung points with a really old set of Dyna 3 Ohm coils from 1978 before they were even called Dyna and a Hondaman electronic points box to assist the points in longivity and performance.

Shelter left shot - forgot fuse box cover
P1040350.JPG
P1040350.JPG (121 KiB) Viewed 694 times
Shelter right
P1040352.JPG
P1040352.JPG (92.05 KiB) Viewed 694 times
Middle shot
P1040353.JPG
P1040353.JPG (114.66 KiB) Viewed 694 times
Tool kit and reprint of owners manual
P1040356.JPG
P1040356.JPG (105.16 KiB) Viewed 694 times
Last edited by flyin900 on Sat Feb 04, 2017 11:23 pm, edited 3 times in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#6

Post by flyin900 »

The bike has finally come together after quite a few challenges that in hindsight were due to maybe cutting corners, yet I see where many on here also don't wish to spend for new parts for every piece replaced. I feel I have about $2400. in parts and machine shop work into the bike plus the purchase price of $300, so it really came out very reasonable overall. I did have some parts help where I can buy batteries, paint, seals and bearings at cost from from my PT job. : crossy.gif

Right front with corbin seat
P1040369.JPG
P1040369.JPG (158.88 KiB) Viewed 694 times
Left front
P1040378.JPG
P1040378.JPG (129.83 KiB) Viewed 694 times
Left rear
P1040365.JPG
P1040365.JPG (134.96 KiB) Viewed 694 times
Motor left
P1040366.JPG
P1040366.JPG (123.7 KiB) Viewed 694 times
Right rear
P1040368.JPG
P1040368.JPG (135.79 KiB) Viewed 694 times
Last edited by flyin900 on Sat Feb 04, 2017 11:25 pm, edited 3 times in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#7

Post by flyin900 »

The rest of these shots are just various angles and close ups of the finished work.

Right front
P1040369.JPG
P1040369.JPG (158.88 KiB) Viewed 694 times
Right front wheel
P1040371.JPG
P1040371.JPG (128.46 KiB) Viewed 694 times
Right switch
P1040374.JPG
P1040374.JPG (93.77 KiB) Viewed 694 times
Left switch
P1040376.JPG
P1040376.JPG (80.67 KiB) Viewed 694 times
Gauge cluster
P1040377.JPG
P1040377.JPG (118.81 KiB) Viewed 694 times
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#8

Post by flyin900 »

Left rear
P1040379.JPG
P1040379.JPG (122.75 KiB) Viewed 694 times
Right rear using GL1200 rear passenger pegs
P1040380.JPG
P1040380.JPG (108.97 KiB) Viewed 694 times
Honda VTX foot peg adapted to Goldwing bracket
P1040381.JPG
P1040381.JPG (95.24 KiB) Viewed 694 times
Stock Goldwing seat
P1040385.JPG
P1040385.JPG (132.12 KiB) Viewed 694 times
Right rear goldwing seat
P1040387.JPG
P1040387.JPG (132.51 KiB) Viewed 694 times
Last edited by flyin900 on Sat Dec 10, 2016 3:12 pm, edited 2 times in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: 1976 GL1000 with LTD wheels- year long project

#9

Post by flyin900 »

Right engine case close up
P1040390.JPG
P1040390.JPG (105.31 KiB) Viewed 694 times
Left engine case
P1040391.JPG
P1040391.JPG (115.18 KiB) Viewed 694 times
Front fender stripe treatment + matching on rear fender
P1040372.JPG
P1040372.JPG (92.57 KiB) Viewed 648 times
Last edited by flyin900 on Sat Dec 10, 2016 11:39 pm, edited 1 time in total.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
Sugs
Gold Member
Gold Member
Posts: 1069
Joined: Sun Aug 09, 2015 6:12 pm
Location: Springfield, MO

Re: 1976 GL1000 with LTD wheels- year long project

#10

Post by Sugs »

Wow, nice job on this. I'm always in awe of you guys that take a restoration to the most minute detail. I don't have the patience.
_______________________

'79 Honda GL1000 Goldwing
User avatar
Oldboy
Silver Member
Silver Member
Posts: 697
Joined: Sat Jul 26, 2008 4:53 pm
Location: Mississauga Ontario Canada

Re: 1976 GL1000 with LTD wheels- year long project

#11

Post by Oldboy »

Great looking....really perfer the stock seat. Fantastic detail work. Sure to be BOTM....at the very least!
Cheers...

Just Wing-it
User avatar
5speed
Honored Life Member
Honored Life Member
Posts: 5311
Joined: Sat Jul 11, 2015 2:37 pm
Location: Nova Scotia Canada

Re: 1976 GL1000 with LTD wheels- year long project

#12

Post by 5speed »

beautiful job...
1982 1100 standard. (sold)
1986 Yamaha FJ1200
2000 Yamaha Roadstar
1976 GoldWing. running but not on the road
1978 Goldwing. future cafe project.
2019 Can-Am ryker (boss's new ride)

2002 Shadow American Classic(sold)
1983 Shadow 500. (sold)
User avatar
Patriccio
Silver Member
Silver Member
Posts: 984
Joined: Thu Mar 07, 2013 3:57 pm
Location: San Diego, Ca.

Re: 1976 GL1000 with LTD wheels- year long project

#13

Post by Patriccio »

Yep, darn good job.
If there is one thing I have learned throughout this process it is this: Check your respirator for spiders before you put it on.
User avatar
Dog Boy
Gold Member
Gold Member
Posts: 1449
Joined: Thu Jun 12, 2008 1:49 pm
Location: Wilmington, Illinois

Re: 1976 GL1000 with LTD wheels- year long project

#14

Post by Dog Boy »

Very nice! Well done!

AL
They call me "Dog Boy"

Can't blame the "PO"
Original owner 76 LTD
Team 993
User avatar
ericheath
Honored Life Member
Honored Life Member
Posts: 9580
Joined: Wed Jul 29, 2009 11:20 am
Location: Winnipeg, Manituba

Re: 1976 GL1000 with LTD wheels- year long project

#15

Post by ericheath »

Awesome work. Thanks for the pics and share.
Whatever I suggest here should be given ample time for a moderator to delicately correct. I apologize in advance.
77 WING, 1200 engine with 77 heads, cams, gl1100 foot pegs, Magna V65 front end, 764A carbs, [-gone Suzuki M109 monoshock--, replaced with gl1100 shocks] gl 1200 swing arm, gl1500 final drive, wheel and rear brakes Valkyrie seat, Meanstreak tank, Sportster pipes, Power Arc ignition off crank.
77 Wing. black
83 Wing, in pieces
"Continuing education is important even if the subject matter is fairly useless (as in this case)."---Greg Foresi
Post Reply
  • Similar Topics
    Replies
    Views
    Last post

Return to “Members Restorations and Projects”